You can buy any old length of chain that you can find, even if it’s quite rusty. If you want to wrap chains around your anvil, then it doesn’t necessarily need to be the newest and fanciest looking chain. To further cut down vibration and noise, try sticking magnets to the underside of your anvil’s horn and tail as well. If you want to use magnets to help silence your anvil, you’ll likely see a major difference just by putting one small bar magnet on the center of the side of your anvil. They’re easier to find and buy than random old used chains in many cases. Many blacksmiths choose to use magnets instead of chains. Magnets can greatly reduce the vibration and noise that an anvil makes. The sand will help keep your anvil stationary and stop it from vibrating. Bolt down a metal or plywood container able to hold about an inch of sand, put your anvil in it, and then cover the remaining area so that the sand can’t get out. In that case, you might want to consider creating a sandbox for your anvil. If the feet of your anvil are warped, then it might be impossible to strap it down properly. This can cut down as much as 80% of the ring. If you do use a stump, be sure to put pieces of metal around the feet of the anvil to hold it in place. I’d recommend not using a wooden stump as a stand for your anvil, as this can cause a lot of extra vibration. This should really be the first step that you take before trying to use chains or magnets to quiet your anvil.īy properly securing your anvil by the corners of its feet, most of the anvil’s ring will go away. Plus less vibration means more energy from your hammering is going directly into the work. If you can eliminate as much vibration as possible, your anvil will be a lot quieter. A little bit of understanding what exactly causes vibration can go a long way. The main thing that makes anvils loud is vibration. If you don’t like the look of having big chains wrapped around your anvil, there are a few other things you can do. But trying to reduce the sound of your anvil a bit is just the courteous thing to do for the sake of your neighbors and other people in the area! Other Methods For Quieting An Anvil You should be wearing ear protection while blacksmithing anyway. And having them improperly secured can make an anvil ring really loud, like you were standing right next to a church bell. It depends on how the anvil was made, as well as how the anvil is secured.Ĭheaper or lower quality anvils tend to ring louder. If you just think wrapping your anvil in a big heavy chain looks cool, you can use it for completely aesthetic reasons.Īre anvils really loud enough that wrapping a chain around them makes enough of a difference? They may have just seen another blacksmith do it before or have seen it used in a movie. Some people aren’t using chains on their anvils for any particular reason. For example, it can give you somewhere to hang your tools while they aren’t in use if you haven’t got any kind of stand or table nearby. Having a chain wrapped around your anvil has some practical reasons while you’re working. The last thing that you want is an anvil sliding around or falling while you’re holding a red hot piece of iron or steel! Practical Reasons Chains are sometimes also used to directly fasten anvils to stands to make sure it doesn’t move during work. Putting heavy chains on your anvil can help add some extra weight to hold it in place. Larger anvils, like 150 pounds or more, aren’t likely to see any benefit from putting chains on them. Anvils around 70 or 80 pounds seem to really benefit from the use of a chain. Putting chains on your anvil seems to work better if you’ve got a small anvil. It seems like wrapping a chain around anvils can offer significant noise reduction on some anvils, but doesn’t do much of anything on others. From my research, I found that it really depends on the anvil. Some people debate whether putting chains on your anvil really has any effect. The main reason that chains are used with anvils is to reduce the amount of noise given off while doing blacksmith work on them. There are a few different reasons why blacksmiths wrap chains around their anvils. 4 Where Can You Buy Cheap Chains? Why Do Blacksmiths Wrap Chains Around Anvils?
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |